
A weak shower can usually be fixed. Low shower pressure normally comes down to one of four things: limescale in the shower head or valve, a problem with the water coming into the house, the type of hot water system you have, or pipework that can't deliver what the shower needs.
This post explains how to tell which one you're dealing with, what you can safely check yourself, and when to call a professional. Cleaning a shower head or checking your stop tap is safe for anyone, but leave the boiler, the hot water cylinder and any electric shower wiring to a qualified person.
Strictly, pressure is how hard the water pushes and flow is how much comes out each minute, but in the shower both feel the same: a disappointing trickle.
Turn on the cold tap in the kitchen. In most homes it comes straight from the mains, so it shows what the water company is sending you. Then try the hot and cold taps in the bathroom.
Your stop tap, the valve where the water main enters your home, is often under the kitchen sink. Thames Water advises checking it is fully open by turning it gently anti-clockwise. If it is stiff, don't force it, as old stop taps can snap or start leaking.
Ask your neighbours whether their water is weak too. If it is, the problem may be on the water company's network, and your supplier's website will show planned work and known problems by postcode.
If you can see small isolation valves on the pipes to the shower, check them too. They have a screw slot: when the slot runs along the pipe the valve is open, and when it sits across the pipe it's closed.
Thames Water, which supplies much of South West London, says all the water in its area is hard. Hard water carries dissolved minerals that leave limescale behind. It builds up in the tiny holes of the shower head and the fine filters inside the valve, narrowing them month by month.
Unscrew the head and soak it in a descaler made for showers, or a mix of white vinegar and water, following the product's instructions. Scrub the nozzles with an old toothbrush, rinse and refit.
If the flow improves, you've found the cause. If it doesn't, the scale may be inside the valve, which needs a plumber to strip down and clean without damaging it.
A gravity-fed system has a cold water tank in the loft feeding a hot water cylinder, often in an airing cupboard. The only push comes from the height of the tank above the shower head, so a top-floor bathroom with little drop from the tank is often weak.
A combi boiler heats water straight from the mains as you use it, so the shower can only be as good as your mains supply and the boiler's output. An unvented cylinder stores hot water at mains pressure and usually gives the strongest showers, but it needs a good mains supply, and the Building Regulations require it to be fitted by a qualified installer.
An electric shower heats its own water, and its flow is limited by the unit's power. If one has slowly weakened, scale inside it is a likely cause, and because it's wired to the mains electricity, that's a job for a qualified person.
With a combi boiler, you may notice your shower weakening from late autumn. The incoming water is much colder in winter, so to reach the same temperature the boiler lets less water through. The shower feels weaker even though nothing is broken.
Avoid running other hot taps while someone showers. If the shower is still poor in milder weather, or a busier household now needs two showers at once, the boiler may simply be too small for your home. Our post on how to tell when your boiler needs replacing explains the signs to look for.
A shower pump is the usual answer to a weak gravity-fed shower. It sits near the cylinder or under the bath and pushes hot and cold water to the shower when you turn it on. On one bathroom renovation we swapped a customer's bath for a walk-in shower and fitted a shower pump as part of the same job.
A standard shower pump is made to draw from a stored tank, not from the mains. Pumps that draw from the mains are covered by the Water Supply (Water Fittings) Regulations 1999, and one drawing more than 12 litres a minute must be notified to the water company before it is fitted. Some approved mains boosters can work with a combi or unvented system, but whether one suits your home depends on your supply.
Never add a pump to a combi boiler or unvented cylinder unless the maker says it is designed for it, as it can damage the system and break the rules above.
Call a plumber if:
Anything involving the boiler must be done by a Gas Safe registered engineer, and work on an electric shower's wiring needs a qualified electrician. Our Gas Safe registered engineers cover this through our boiler installation service.
If your shower has never been quite right, or it's part of a bathroom you're planning to update, Riverside Construction Group can visit, assess your existing plumbing and hot water system, and talk you through what will actually make a difference before any work starts. You can arrange a visit through our bathroom installation service.